What is the connection ch3 ch3

Audio set parameters

For specifying the reference input level when the [INPUT1] selector switch is set to “MIC” or “MIC + 48V”.

[Setting values: -60 dB, -50 dB, -40 dB, -30 dB]

For specifying the reference input level when the [INPUT2] selector switch is set to “MIC” or “MIC + 48V”.

[Setting values: -60 dB, -50 dB, -40 dB, -30 dB]

For adjusting the sensitivity of the [AUX] input connector.

[Setting values: + 12dB, + 6dB, 0dB, ​​-6dB, -12dB]

For setting the mode and input level for [CH-3] and [CH-4].

For setting the reference recording level of [CH-1] and [CH-2]. (Applies to both [CH-1] and [CH-2].)

[Setting values: -12dB, -18dB, -20dB]

For setting the reference recording level of [CH-3] and [CH-4]. (Applies to both [CH-3] and [CH-4].)

CH1 / 2 -12dB:
Adjusts to a value 12 dB lower than that of [CH-1] and [CH-2].

CH1 / 2 -6dB:
Adjusts to a value 6 dB lower than that of [CH-1] and [CH-2].

CH1 / 2 Link:
Sets to the same value as [CH-1] and [CH-2].

[Setting values: CH1 / 2 -12dB, CH1 / 2 -6dB, CH1 / 2 Link]

Sets whether the limiter operation of [CH-1] and [CH-2] should be linked.
Select “Link” to link and “Separate” to disconnect.

[Setting values: Link, Separate]

This option can only be selected when both the [AUDIO SELECT CH-1] and [AUDIO SELECT CH-2] selector switches are set to “AUX” and the [AUDIO SELECT CH-1 / CH-2 AUTO / MANUAL] selector switch is set to “AUTO” at the same time.
This option can only be selected when the [AUDIO SELECT CH-1] selector switch is set to “INPUT1”, the [AUDIO SELECT CH-2] selector switch is set to “INTPUT2”, and the [AUDIO SELECT CH-1 / CH-2 AUTO / MANUAL] selector switch is set to “AUTO” at the same time.
In all other cases it is fixed on “Separate”.

Sets the operation for the limiter for [CH-1] and [CH-2] separately.

Sets the maximum recording level of [CH-1] and [CH-2] accordingly.

[Setting values: -17 dBFS, -15 dBFS, -12 dBFS, -9 dBFS, -6 dBFS, off]

Sets the time to activate the limiter for [CH-1] and [CH-2] accordingly.

[Setting values: Fast, Middle, Slow]

Sets the time to disable operation for the limiter for [CH-1] and [CH-2] accordingly.

[Setting values: Fast, Middle, Slow]

Sets whether the limiter operation of [CH-3] and [CH-4] should be linked.
Select “Link” to link and “Separate” to separate.

[Setting values: Link, Separate]

This option can only be selected when both the [AUDIO SELECT CH-3] and [AUDIO SELECT CH-4] selector switches are set to “AUX” and [Audio Set] [CH3 / 4 input level] [CH3] / [CH4] is set to “Auto” at the same time.
This option can only be selected when the [AUDIO SELECT CH-3] selector switch is set to “INPUT1”, the [AUDIO SELECT CH-4] selector switch is set to “INTPUT2”, and [Audio Set] [CH3 / 4 input level] [CH3] / [CH4] is set to “Auto” at the same time.
In all other cases it is fixed on “Separate”.

Sets the operation for the limiter for [CH-3] and [CH-4] separately.

Sets the maximum recording level of [CH-3] and [CH-4] accordingly.

[Setting values: -17 dBFS, -15 dBFS, -12 dBFS, -9 dBFS, -6 dBFS, off]

Sets the time to activate the limiter for [CH-3] and [CH-4] accordingly.

[Setting values: Fast, Middle, Slow]

Sets the time to disable operation for the limiter for [CH-3] and [CH-4] accordingly.

[Setting values: Fast, Middle, Slow]

CH1 filter to CH4 filter

For setting the input signals for [CH-1] to [CH-4] up to Wind Cut, Equalizer or Off, respectively.

[Setting values: Equalizer, Wind Cut, Off]

When the [AUDIO INPUT] signal selection switch 1 setting of [CH-1] in the [CH1 Filter] parameter is set to “LINE”, “-” is displayed and the selection is disabled.

When [CH2 Filter] is set as follows, “-” is displayed and the selection is disabled.

When [CH-2] is set to “INPUT1” and the setting of [AUDIO INPUT] signal selection switch 1 is set to “LINE”

When [CH-2] is set to “INPUT2” and the setting of the [AUDIO INPUT] signal selection switch 2 is set to “LINE”

When the [AUDIO INPUT] signal selection switch 1 setting of [CH-3] in the [CH3 Filter] parameter is set to “LINE”, “-” is displayed and the selection is disabled.

When [CH4 Filter] is set as follows, “-” is displayed and the selection is disabled.

When [CH-4] is set to “INPUT1” and the setting of [AUDIO INPUT] signal selection switch 1 is set to “LINE”

When [CH-4] is set to “INPUT2” and the setting of the [AUDIO INPUT] signal selection switch 2 is set to “LINE”

You can use this equalizer setting to correct characteristics and improve the sound of the connected microphone.

For setting the audio frequency of a 5-band equalizer.

Frequency:
100 Hz, 330Hz, 1kHz, 3.3 kHz, 10 kHz

Variable level:
± 6 dB (0.5 dB step)

Audio signals are recorded according to the characteristics set on the equalizer.

Set "0dB" for all bands to use the equalizer bypass.

When the equalizer level is set to the + side, the sound may be distorted. In this case, reduce the recording level manually.

If the values ​​of several frequencies are changed, the specified and actual values ​​may turn out different due to interference between the frequency bands.

Cannot be selected if none of the parameters from [CH1 Filter] to [CH4 Filter] are set to "Equalizer".

Sets the channel to be output to the [AUDIO OUTPUT] and [HDMI] terminals.

CH3 / 4:
Outputs the audio from [CH-3] and [CH-4].

CH1 / 2:
Outputs the audio from [CH-1] and [CH-2].

SW set:
Outputs according to the setting of the [MONITOR SELECT] switch.

[Setting values: CH3 / 4, CH1 / 2, SW set]

For setting the audio sound of the [PHONES] connector to stereo or mixed sound when the [MONITOR] selector switch on the handle is set to “BOTH”.

Mix:
Output of mixed sound (mixed sound of channel 1 and channel 2) to both L and R.

Stereo:
Outputs stereo sound (outputs audio sound from CH-1 to L, and CH-2 to R).

[Setting values: Mix, stereo]

Selects whether the warning tone is activated and is also used to adjust the volume.
The warning tone is output through the monitor speaker or the [PHONES] terminal.

[Setting Values: Off, 1 to 5] ( 5)

Specifies whether an audio test signal (1 kHz) is output while the test pattern is displayed.

[Setting values: On, Off]